When Kenwood dishwashers stop working, you should check the error code to find out what went wrong. This guide will introduce you to some of the error codes you may encounter.
Kenwood Dishwasher Error Codes – Why?
Error codes are not random. They appear because of one or more of the following factors:
1). Obstructions In The Pipes & Drains
Water pressure problems attract error codes because water is vital to a dishwasher’s operations. Kitchen Snitches have seen error codes in appliances with the wrong water pressure, leakages, and obstructions in the pipes and drains.
The dishwasher generates an error code when it detects these issues because the unit cannot deliver satisfying results until you resolve these problems.
2). Defective Flow Meter
The flow meter in the air brake system can develop defects. If it fails to communicate with the PCB, the dishwasher may detect a problem regarding the amount of water entering the tank. As a result, the appliance will show you an error code.
3). Plastic Holder Is Too Loose
Some people blame the thermostat for everything that goes wrong. But sometimes, the fault lies with the plastic holder, the component holding the thermostat against the drum. If the plastic holder is too loose to make a good connection, the dishwasher will show you an error code.
4). Dishes Not Arranged Properly
Did you load the dishes properly? Some dishwashers generate weird sounds because you arranged the dishes poorly, and they keep knocking against each other. But this is not the only warning you can expect. Some dishwashers are sophisticated enough to alert you with error codes if you load the dishes incorrectly.
5). Forget To Add Detergent
Did you add detergent to the appliance? Some people forget to add detergent. Others add too much detergent. You also have consumers that use the wrong detergent. The dishwasher won’t flash an error code specifically because you used the wrong detergent.
Instead, it will show an error code that doesn’t make sense. For instance, it may complain that you loaded the dishes incorrectly, even though that is not the case. Some people will spend hours inspecting every component in the appliance before it occurs to them to check on the detergent.
6). Door Is Open
You don’t want to run the appliance when the door is open. You will make a mess of the kitchen. Fortunately, the dishwasher is smart enough to identify this issue. It will warn you via an error code, giving you an opportunity to close the door securely.
Kenwood Dishwasher Error Codes F1 Meaning
You can blame this issue on excess water in the bottom catch basin. Flooding has various sources, including leakages originating from damaged door seals and blocked hoses. You should also inspect the electronic parts for moisture.
How To Fix It?
Don’t proceed until you disconnect the appliance from the power source. If the device is hard-wired, use the breaker to cut the power before accessing the bottom tray and removing the water.
Tip the tray back by 45 degrees. Don’t put it back until the tray is sufficiently dry. Restore the power and wait. If the error code persists, you have moisture in the electronic components.
If the error code goes away and returns, find the source of the flooding. Replace damaged door seals and hoses. Otherwise, the leaks will continue.
Kenwood Dishwasher Error Codes F2 Meaning
You have a blockage somewhere, probably in the pipe or the pump. Get your tools and start troubleshooting the appliance. Inspect the sump. If you can’t see any blockages, turn your attention to the filter. Don’t forget the waste pipe.
How To Fix It?
- Check the drain pipe. If it has obstructions, remove them.
- Look for kinks in the drain hose and remove them.
- Look for blockages in the filter. You can either clean or replace the filter, depending on your observation.
- Clear the blockages in the sump.
- Perform a reset by shutting the dishwasher off, disconnecting it from the power source, waiting a few minutes, and reconnecting it.
Kenwood Dishwasher Error Codes F5 Meaning
The spray arms are either clogged or damaged. Defective spray arms cannot clean your dishes satisfactorily.
How To Fix It?
Disconnect the power and check the spray arms for blockages. Some blockages are impossible to identify unless you unscrew the spray arms. If you don’t have the skill or experience, ask an expert to inspect and replace worn-out bearing rings.
Check the drain pipe as well. Clogging in the drain pipe may attract an F5 error.
Kenwood Dishwasher Error Code F6 Meaning
- You have a faulty heat sensor
- Faulty control board
- Loose or damaged wiring
- Overheating during the wash cycle
How To Fix It?
Either the dishwasher is overheating, or the sensor is defective. You need the assistance of a technician. They can fix or replace the sensor and control board.
They can also find and replace damaged wiring. This assumes that the wiring is at fault. Who installed the appliance? Does it have access to cold water? If you installed this device yourself, ask the technician to inspect your work. You probably made a mistake.
Kenwood Dishwasher Error Codes F9 Meaning
- This is a divisor position error associated with the flow meter.
- You have controller or sensor errors.
How To Fix It?
- Inspect the spray arms. Clean them where necessary.
- Inspect the drain hose and pump. Clean them if they need it.
- Ask a technician to inspect and replace defective controllers and sensors.
Kenwood Dishwasher Error Codes FF Meaning
- Blocked filter
- Blocked hose
- You did not remove the plug from the point where the drain and garbage disposal connect.
- Poorly configured drain hose
- Defective drain pump
- Broken drain pump impeller
How To Fix It?
- Replace a defective drain pump
- Clean or replace the filter
- Clean or replace the hose
- Remove the plug from the point where the drain and garbage disposal connect.
Kenwood Dishwasher Error Codes E1 Meaning
- The tap is in the off position
- Broken flow meter
- You have a leak somewhere, probably in the drain hose
- Damaged impeller
- Faulty pressure switch
- Faulty control board
How To Fix It?
- Make sure the faucet is fully open.
- Check the supply line and remove any kinks you notice
- Remove blockages from the drain hose
- Replace leaking pipes and hoses
- Replace a defective impeller
- Replace a faulty control board
- Replace a faulty pressure switch
Kenwood Dishwasher Error Codes E3 Meaning
The water is not hot enough, or it is taking too long to get hot. This problem has several potential sources, including a defective heating element and a faulty sensor. You probably have a malfunctioning heating circuit.
How To Fix It?
- Test the pressure switch. If it isn’t clicking, the component is defective. Get a replacement.
- Clean or replace the temperature sensor.
- Replace a defective safety thermostat
- Replace broken wires
- Fix loose connections
- Fix a broken heater element
Kenwood Dishwasher Error Codes E4 Meaning
- Damaged or disconnected hose
- The anti-flood device is activated. You have a leak somewhere.
How To Fix It?
E4 incites panic because it means that water is overflowing in the dishwasher. The solution is relatively straightforward. Disconnect the dishwasher from its power source and tilt it back at a 45-degree angle to drain the water.
Look for clogs in the drain hose. You should also search for damaged seals. Don’t reconnect the dishwasher until you dry the appliance.
Kenwood Dishwasher Error Codes E7 Meaning
- Faulty heating element
- Defective thermostat
- Compromised water supply
- Short circuit
- Faulty temperature sensor
How To Fix It?
You need a technician to inspect the defective components to determine whether or not you should replace them. In some situations, you can get away with cleaning the sensor and improving the water pressure.
Kenwood Dishwasher Error Code E8 Meaning
- Faulty diverter valve
How To Fix It?
- Check the micro switch, motor, and reduction gears. You can fix a stiff paddle by soaking the part in boiling water.
Kenwood Dishwasher Error E9 Meaning
- The dishwasher is overfilled.
How To Fix It?
- Find the thin hose that connects to the pressure switch and clear the accumulated muck.
- Replace a faulty pressure switch
- Replace a defective control board
- Replace a defective flow meter
Kenwood Dishwasher Error Code H3 Meaning
Your appliance has an electronic glitch. You rarely see H3 error codes in Kenwood dishwashers.
How To Fix It?
Perform a reset. Shut the appliance down and disconnect it from the wall outlet. Wait several minutes and reconnect it. You can try performing multiple resets. Otherwise, contact Kenwood’s customer support staff. Use your warranty to get free repairs or a replacement.
Kenwood Dishwasher Error Code 4 Meaning
Error code 4 appears when an overflow occurs. You have excess water in the dishwasher. This means a leak has occurred somewhere. If it goes unchecked, water will invade the sensitive electronic components of the appliance.
How To Fix It?
Unplug the dishwasher and tip it backward. This means pulling the appliance away from the wall. Tilting it back by 45 degrees allows the excess water to drain out. You should check the hose for clogging to be on the safe side.
Dry the dishwasher and reconnect it. If the error code appears, ask an electrician to inspect the control board and sensor. He will replace them where necessary.
Kenwood Dishwasher Error Code 188 Meaning
You have an electronic glitch or a faulty control board. 188 is not one of Kenwood’s error codes. If you’re seeing it, something has gone wrong. A glitch is the most probable culprit.
How To Fix It?
Perform a hard reset. This involves turning the dishwasher off and holding the program button. Maintain your hold on this button as you start the dishwasher. Wait until all the lights come on before you let go of the start button.
The final step is to turn the dishwasher off and on again. If the 188 error code persists, inspect the control board. You should consider replacing it. Send the dishwasher to a technician if the error code returns despite the new control board.
Related post: